Advertisement
Quick Links
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT:
INSTALLER:
OWNER:
WARNING: TO REDUCE
THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PER-
SONS, OBSERVE THE FOL-
LOWING:
CAUTION: FOR GENERAL
VENTILATING USE ONLY. DO
NOT USE TO EXHAUST HAZ-
ARDOUS OR EXPLOSIVE MA-
TERIALS OR VAPORS.
A. Use this unit only in the manner
intended by the manufacturer. If you
have questions, contact the manufac-
turer.
B. Before servicing or cleaning unit,
switch power off at service panel and
lock the service disconnecting means
to prevent power from being switched
on accidentally. When the service dis-
WARNING - TO REDUCE THE RISK OF A RANGE
TOP GREASE FIRE:
A. Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
B. Always turn hood ON when cooking at high heat or
when cooking flaming foods.
C. Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
D. Use proper pan size. Always use cookware appropriate
for the size of the surface element.
Save these instructions for the Local Electrical Inspector's use.
Please leave these Installation Instructions with this unit for the owner.
Please retain these instructions for future reference.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
connecting means cannot be locked,
securely fasten a prominent warning
device, such as a tag, to the service
panel.
C. Installation work and electrical
wiring must be done by qualified per-
sons in accordance with all applicable
codes & standards, including fire-rated
construction.
D. Sufficient air is needed for proper
combustion and exhausting of gases
through the flue (chimney) of fuel burn-
ing equipment to prevent backdrafting.
Follow the heating equipment manu-
facturers guideline and safety standards
such as those published by the Na-
tional Fire Protection Association
(NFPA), the American Society for Heat-
ing, Refrigeration and Air Conditioning
INSTALLATION INSTRUCTIONS
VCH36 OR VCH54
FOR RESIDENTIAL USE ONLY
Engineers (ASHRAE), and the local
code authorities.
E. When cutting or drilling into wall
or ceiling, do not damage electrical
wiring and other hidden utilities.
F. CAUTION: To reduce risk of
fire and to properly exhaust air, be
sure to duct air outside. Do not vent
exhaust air into spaces within walls,
ceilings, attics, crawl spaces or garages.
G. WARNING – TO REDUCE
THE RISK OF FIRE, USE ONLY METAL
DUCT WORK.
H. Install this hood in accordance
with all requirements specified by the
manufacturer of your cooktop/range.
WARNING: - TO REDUCE THE RISK OF INJURY
TO PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING:
A. SMOTHER FLAMES with a close-fitting lid, cookie
sheet, or metal tray, then turn off the burner. BE CAREFUL
TO PREVENT BURNS. If the flames do not go out
immediately, EVACUATE AND CALL THE FIRE
DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN – You may be burned.
C. DO NOT USE WATER, including wet dishcloths or
towels – a violent steam explosion will result.
D. Use an extinguisher ONLY if:
1) You have a Class ABC extinguisher, and you already
know how to operate it.
2) The fire is small and contained in the area where it
started.
3) The fire department is being called.
4) You can fight the fire with your back to an exit.
Advertisement
Related Manuals for Thermador VCH36
Summary of Contents for Thermador VCH36
-
Page 1: Installation Instructions
INSTALLATION INSTRUCTIONS VCH36 OR VCH54 FOR RESIDENTIAL USE ONLY PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. INSTALLATION MUST COMPLY WITH ALL LOCAL CODES. IMPORTANT: Save these instructions for the Local Electrical Inspector’s use. INSTALLER: Please leave these Installation Instructions with this unit for the owner. - Page 2 (maximum) reflector type light bulbs for 120 volts, 60 Hz. The VCH36 has one built-in filter box and two lights. The 4. COLD WEATHER installations should have a backdraft VCH54 has two built-in filter boxes and three lights. Con- damper installed to minimize backward flow of cold air, and nect power supply wires per local code.
- Page 3 (Front Panel opens to remove FIGURE 1B filter) I. The VCH36/VCH54 are designed to be installed in HEATING a custom hood as shown in Figure IA. Design of the hood must meet all building code regulations and is the responsibility of the contractor. For optimal...
- Page 4 Thermador reserves the right to change specifications or design without notice. Some models are certified for use in Canada. Thermador is not responsible for products which are transported from the United States for use in Canada. Check with your local Canadian distributor or dealer.